Chainsaw chain
Husqvarna X-CUT C33 chain loop 585 64 11-66 (66 drive links, 40 cm bar)
585 64 11-66
Fits 1 model
Wrong part, or your model missing? Tell us. A person checks every report.
GenuineGenuine Husqvarna
$49.00
Husqvarna Australia · 30 OctLowest genuine · Husqvarna Australia · checked 30 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Husqvarna. Compatible: another brand.Genuine is made by Husqvarna. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $49.00
Husqvarna Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
Opens Husqvarna Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the cutting teeth are worn down to 4 mm (5/32 in), Husqvarna says; sharpen them when the chain cuts poorly.
After replacing: No reset needed. Check the chain tension often until a new chain has run in, Husqvarna says.
How to change the 585 64 11-66 chain
Watch the guide or follow the steps.
- 1Stop the saw (on a battery saw, take the battery out) and put on protective gloves.
- 2Remove the bar nuts and the clutch cover, and slacken the chain tensioning screw.
- 3Take off the old chain. Lift the new chain over the drive sprocket and into the bar groove, starting at the top edge of the bar, with the cutter edges facing forward on the top of the bar.
- 4Refit the clutch cover with the chain adjuster pin in the hole in the bar, and tighten the bar nuts finger-tight.
- 5Turn the tensioning screw clockwise until the chain does not hang below the bar but still turns easily by hand.
- 6Hold up the nose of the bar and tighten the bar nuts with the combination wrench. Check the tension often until the new chain has run in.
Every number this part goes by
- Retail name:
- 585 64 11-66
- Retail name:
- 585-64-11-66
- Retail name:
- 585641166
- Retail name:
- C33 66
Sellers list any of these; they are the same part.
Will it fit your appliance?
Type your model number and we'll check it against the makers' lists.
Fits this Husqvarna model
Husqvarna1 model
With a 40 cm (16 in) bar: 66 drive links.
Common questions
- What does the 585 64 11-66 fit?
- The Husqvarna X-CUT C33 chain loop 585 64 11-66 (66 drive links, 40 cm bar) fits the Husqvarna 550i XP.
- Where can I buy the 585 64 11-66 in Australia?
- We track 1 Australian seller for the 585 64 11-66; the lowest listed price when we last checked was A$49.00 at Husqvarna Australia. Prices are re-checked daily and dated on this page.
- How do I fit the 585 64 11-66?
- 6 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A blunt or stretched chain cuts slowly, throws dust instead of chips, and makes the saw harder to control.
- Is there anything to reset afterwards?
- No reset needed. Check the chain tension often until a new chain has run in, Husqvarna says.
Something looks wrong with the 585 64 11-66 match? . Reports go to a person, not a bot.