Salt chlorinator cell
AstralPool Viron V25, eQuilibrium EQ25 and Halo Chlor 25 complete cell 12906
12906
Fits 3 models
Wrong part, or your model missing? Tell us. A person checks every report.
GenuineGenuine AstralPool
$1165.00
Pool & Spa Warehouse · 31 OctLowest genuine · Pool & Spa Warehouse · checked 31 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by AstralPool. Compatible: another brand.Genuine is made by AstralPool. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $1165.00
Pool & Spa Warehouse. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 3 sellers
AUD, before delivery. Each price shows when it was checked.
Genuine AstralPool
3 sellers
Opens Pool & Spa Warehouse in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the controller keeps showing low salt, no flow or low output after the salt level has been checked and the cell cleaned, AstralPool says; check the cell for calcium every fortnight.
After replacing: No reset needed. After fitting, run the pump, switch the chlorinator on and set the output again; the low-salt or no-flow warning should clear once water is flowing through the new cell.
How to change the 12906 chlorinator cell
Watch the guide or follow the steps.
- 1Turn the chlorinator off at the power point, turn the filter pump off and close the valves either side of the cell if you have them.
- 2Disconnect the cell lead: on the VX and Viron undo the wing nuts (note the blue wire is on the blue terminal); on the E-Series and eQuilibrium unplug the cell terminal cap; on the Halo unclip the end cap.
- 3Undo the two barrel unions and lift the old cell out of the pipework.
- 4Fit the new cell level, with the barrel unions underneath, the O-rings seated and the water entering at the end nearest the terminals (follow the flow label). Tighten the unions.
- 5Reconnect the lead, open the valves, start the pump and check for leaks, then switch the chlorinator on and set the output.
Every number this part goes by
- Retail name:
- 12906
Sellers list any of these; they are the same part.
Will it fit your appliance?
Type your model number and we'll check it against the makers' lists.
Fits these 3 AstralPool models
AstralPool3 models
Complete cell (electrode and clear housing): buy this if your housing is cracked, crazed or leaking. If the housing is sound, the electrode on its own is enough.
Common questions
- What does the 12906 fit?
- The AstralPool Viron V25, eQuilibrium EQ25 and Halo Chlor 25 complete cell 12906 fits the AstralPool Halo Chlor 25, Viron eQuilibrium EQ25 and Viron V25.
- Where can I buy the 12906 in Australia?
- We track 3 Australian sellers for the 12906; the lowest listed price when we last checked was A$1165.00 at Pool & Spa Warehouse. Prices are re-checked daily and dated on this page.
- How do I fit the 12906?
- 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A worn cell makes too little chlorine, so the water turns green or cloudy, and turning the output up only wears it faster.
- Is there anything to reset afterwards?
- No reset needed. After fitting, run the pump, switch the chlorinator on and set the output again; the low-salt or no-flow warning should clear once water is flowing through the new cell.
Something looks wrong with the 12906 match? . Reports go to a person, not a bot.