Salt chlorinator cell
AstralPool Viron V18, eQuilibrium EQ18 and Halo Chlor 18 electrode 12915
12915
Fits 3 models
Wrong part, or your model missing? Tell us. A person checks every report.
GenuineGenuine AstralPool
$930.00
Pool & Spa Warehouse · 31 OctLowest genuine · Pool & Spa Warehouse · checked 31 Oct
CompatibleCompatible option
$575.00
Pool & Spa Warehouse · 31 OctPool & Spa Warehouse · checked 31 Oct
Check sellerCheck seller details
Genuine: made by AstralPool. Compatible: another brand.Genuine is made by AstralPool. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest compatibleLowest compatible price · $575.00
Pool & Spa Warehouse. Compare with genuine below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 6 listings from 4 sellers
AUD, before delivery. Each price shows when it was checked.
Compatible options
2 sellers
Genuine AstralPool
4 sellers
Opens Pool & Spa Warehouse in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the controller keeps showing low salt, no flow or low output after the salt level has been checked and the cell cleaned, AstralPool says; check the cell for calcium every fortnight.
After replacing: No reset needed. After fitting, run the pump, switch the chlorinator on and set the output again; the low-salt or no-flow warning should clear once water is flowing through the new cell.
How to change the 12915 chlorinator cell
Watch the guide or follow the steps.
- 1Turn the chlorinator off at the power point, turn the filter pump off and close the valves either side of the cell if you have them.
- 2Disconnect the cell lead: on the VX and Viron undo the wing nuts (the blue sensor wire goes back on the blue terminal); on the E-Series and eQuilibrium unplug the cell terminal cap; on the Halo unclip the end cap and unplug the colour-coded wires.
- 3Unscrew the cell nut (retaining ring) and draw the old electrode out of the clear housing. If the housing is cracked, crazed or weeping, fit a complete cell instead.
- 4Slide the new electrode in with its O-ring seated, screw the nut back on firmly by hand and reconnect the lead the way it came off.
- 5Open the valves, start the pump and check for leaks, then switch the chlorinator back on and set the output.
Every number this part goes by
- Retail name:
- 12915
Sellers list any of these; they are the same part.
Will it fit your appliance?
Type your model number and we'll check it against the makers' lists.
Fits these 3 AstralPool models
AstralPool3 models
Viron eQuilibrium EQ18. Electrode only: it slides into your existing clear housing and is held by the cell nut. Covers the current Bluetooth eQ (13803) and the earlier eQuilibrium (12803).
The other 2 models. Electrode only: it slides into your existing clear housing and is held by the cell nut.
Common questions
- What does the 12915 fit?
- The AstralPool Viron V18, eQuilibrium EQ18 and Halo Chlor 18 electrode 12915 fits the AstralPool Halo Chlor 18, Viron eQuilibrium EQ18 and Viron V18.
- Where can I buy the 12915 in Australia?
- We track 4 Australian sellers for the 12915; the lowest listed price when we last checked was A$575.00 at Pool & Spa Warehouse. Prices are re-checked daily and dated on this page.
- How do I fit the 12915?
- 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A worn cell makes too little chlorine, so the water turns green or cloudy, and turning the output up only wears it faster.
- Is there anything to reset afterwards?
- No reset needed. After fitting, run the pump, switch the chlorinator on and set the output again; the low-salt or no-flow warning should clear once water is flowing through the new cell.
Something looks wrong with the 12915 match? . Reports go to a person, not a bot.