How do I fit the 9FWBR200000?

No tools, a few minutes: 4 steps, listed on this page with the replacement video where the maker has one.

What happens if I don't change it?

A worn or matted roller picks up less; on a floor cleaner it also leaves streaks and water behind.

Hard floor cleaner roller

Tineco brush roller for Floor One S6, S6 Pro Extreme and S7 Pro

9FWBR200000

Fits 3 models · replace every 6 months

Wrong part, or your model missing? Tell us. A person checks every report.

GenuineGenuine Tineco

$34.90

Tineco Australia · 2 NovLowest genuine · Tineco Australia · checked 2 Nov

CompatibleCompatible option

See seller

No compatible seller tracked yetNo compatible seller tracked yet

Genuine: made by Tineco. Compatible: another brand.Genuine is made by Tineco. Compatible is made by another brand. Check the seller's page for the size and models it fits.

Lowest price · $34.90

Tineco Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.

Open Tineco Australia · $34.90

Compare 1 seller

AUD, before delivery. Each price shows when it was checked.

Genuine Tineco

1 seller

Tineco AustraliaGenuine · checked 2 NovGenuine part · Lowest genuinechecked 2 Nov$34.90OpenGo to seller

Open cheapest seller · $34.90

Opens Tineco Australia in a new tab. Their page is the source of truth for price, delivery and returns.

How long it lasts

Usually every 6 months (every 6 months, Tineco says in its S7 Pro manual (its S6 manual says every 8 months)).

After replacing: No reset: the maker's manual describes no replacement reminder for this part.

Not due yet?

Get a nudge when your roller is due — it's every 6 months. One email two weeks before, no newsletter. Manage or stop it anytime.

How to change the 9FWBR200000 roller

Watch the guide or follow the steps.

How to use | Tineco FLOOR ONE S7 PRO | EN · Tineco Support (official)

1Take the cleaner off its base and empty the dirty water tank first.
2Grab the brush roller tab and pull the roller out.
3Pull the roller handle (tab) off the old roller and fit it onto the new one. Do not pull on the roller's pull ring.
4Insert the end of the new roller into the left side of the holder, then attach the tab to the magnetic buckle on the right until it locks.

Every number this part goes by9FWBR200000

Retail name:: 9FWBR200000

Sellers list any of these; they are the same part.

Will it fit your appliance?

Type your model number and we'll check it against the makers' lists.

Your appliance model

Fits these 3 Tineco modelsFloor One S6, Floor One S6 Pro Extreme, Floor One S7 Pro

Tineco3 models

Common questionsWhat does the 9FWBR200000 fit? · How often should I replace the 9FWBR200000? · Where can I buy the 9FWBR200000 in Australia?

What does the 9FWBR200000 fit?: The Tineco brush roller for Floor One S6, S6 Pro Extreme and S7 Pro (part 9FWBR200000) fits the Tineco Floor One S6, Floor One S6 Pro Extreme and Floor One S7 Pro.
How often should I replace the 9FWBR200000?: Every 6 months, or sooner if it looks worn.
Where can I buy the 9FWBR200000 in Australia?: We track 1 Australian seller for the 9FWBR200000; the lowest listed price when we last checked was A$34.90 at Tineco Australia. Prices are re-checked daily and dated on this page.
How do I fit the 9FWBR200000?: No tools, a few minutes: 4 steps, listed on this page with the replacement video where the maker has one.
What happens if I don't change it?: A worn or matted roller picks up less; on a floor cleaner it also leaves streaks and water behind.
Is there anything to reset afterwards?: No reset: the maker's manual describes no replacement reminder for this part.

Something looks wrong with the 9FWBR200000 match? . Reports go to a person, not a bot.