The Husqvarna 120e Mark II takes the Husqvarna X-CUT S93G chain loop 585 40 42-56 (56 drive links, 40 cm bar) as its chain; Australian sellers list it from A$40.00 as of 30 October 2026. Fitment confirmed against the manufacturer's compatibility list.
Your chainsaw
Husqvarna 120e Mark II
Chainsaw
Confirmed against Husqvarna's listConfirmed against Husqvarna's own compatibility list
Not yours? Change
Takes the 585 40 42-56 chain
X-CUT S93G chain loop 585 40 42-56 (56 drive links, 40 cm bar) · check the code on your old part before ordering.
Husqvarna Australia lists the 120e Mark II with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
Your chainsaw
Chainsaw
Confirmed against Husqvarna's listConfirmed against Husqvarna's own compatibility list
Takes the 585 40 42-56
Chain · check the code on your old part.
Husqvarna Australia lists the 120e Mark II with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
Other Husqvarna chainsaws that take the 585 40 42-56
GenuineGenuine Husqvarna
$40.00
Husqvarna Australia · 30 OctLowest genuine · Husqvarna Australia · checked 30 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Husqvarna. Compatible: another brand.Genuine is made by Husqvarna. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $40.00
Husqvarna Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
Opens Husqvarna Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the cutting teeth are worn down to 4 mm (5/32 in), Husqvarna says; sharpen them when the chain cuts poorly.
After replacing: No reset needed. Check the chain tension often until a new chain has run in, Husqvarna says.
How to change the chain in your Husqvarna 120e Mark II
Watch the guide or follow the steps.
- 1Stop the saw (on a battery saw, take the battery out) and put on protective gloves.
- 2Remove the bar nuts and the clutch cover, and slacken the chain tensioning screw.
- 3Take off the old chain. Lift the new chain over the drive sprocket and into the bar groove, starting at the top edge of the bar, with the cutter edges facing forward on the top of the bar.
- 4Refit the clutch cover with the chain adjuster pin in the hole in the bar, and tighten the bar nuts finger-tight.
- 5Turn the tensioning screw clockwise until the chain does not hang below the bar but still turns easily by hand.
- 6Hold up the nose of the bar and tighten the bar nuts with the combination wrench. Check the tension often until the new chain has run in.
Every number this part goes by
- Retail name:
- 585 40 42-56
- Retail name:
- 585-40-42-56
- Retail name:
- 585404256
- Retail name:
- S93G 56
Sellers list any of these; they are the same part.
About your Husqvarna 120e Mark II
Husqvarna chainsaw — Petrol chainsaws (home). Its chain is the X-CUT S93G chain loop 585 40 42-56 (56 drive links, 40 cm bar), part 585 40 42-56.
Other chains the maker lists for this chainsaw: Husqvarna X-CUT S93G chain loop 585 40 42-52 (52 drive links, 35 cm bar). With a 35 cm (14 in) bar: 52 drive links.
Where the model number is: The model is on the rating plate on the saw's housing (STIHL MS 170, Husqvarna 135 Mark II, Ryobi OCS1830BL). The chain's code is stamped on the drive links or printed on its box, and the bar length is on the bar.
Fits these 5 Husqvarna models
Husqvarna5 models
120e Mark II. Husqvarna Australia lists the 120e Mark II with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
130. Husqvarna Australia lists the 130 with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
135 Mark II. Husqvarna Australia lists the 135 Mark II with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
The other 2 models. With a 40 cm (16 in) bar: 56 drive links.
Common questions
- Which chain fits the Husqvarna 120e Mark II?
- The Husqvarna 120e Mark II takes the Husqvarna X-CUT S93G chain loop 585 40 42-56 (56 drive links, 40 cm bar). Husqvarna Australia lists the 120e Mark II with a 40 cm (16 in) bar: 585 40 42-56, 56 drive links. Other bar lengths take other loops.
- Where can I buy the 585 40 42-56 in Australia?
- We track 1 Australian seller for the 585 40 42-56; the lowest listed price when we last checked was A$40.00 at Husqvarna Australia. Prices are re-checked daily and dated on this page.
- How do I fit the 585 40 42-56 in a Husqvarna 120e Mark II?
- 6 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A blunt or stretched chain cuts slowly, throws dust instead of chips, and makes the saw harder to control.
- Is there anything to reset afterwards?
- No reset needed. Check the chain tension often until a new chain has run in, Husqvarna says.
Something looks wrong with the 120e Mark II match? . Reports go to a person, not a bot.