The Pool Controls SG30 takes the Pool Controls SG30 replacement cell 00551335 as its cell; Australian sellers list it from A$795.00 as of 1 November 2026. Fitment confirmed against the manufacturer's compatibility list.
Your salt chlorinator
Pool Controls SG30
Salt chlorinator
Confirmed against Pool Controls's listConfirmed against Pool Controls's own compatibility list
Not yours? Change
Takes the 00551335 cell
SG30 replacement cell 00551335 · check the code on your old part before ordering.
Cell only: it fits your existing cell housing under the housing nut.
Your salt chlorinator
Salt chlorinator
Confirmed against Pool Controls's listConfirmed against Pool Controls's own compatibility list
Takes the 00551335
Cell · check the code on your old part.
Cell only: it fits your existing cell housing under the housing nut.
Other Pool Controls salt chlorinators that take the 00551335
GenuineGenuine Pool Controls
$795.00
Budget Pool Care · 1 NovLowest genuine · Budget Pool Care · checked 1 Nov
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Pool Controls. Compatible: another brand.Genuine is made by Pool Controls. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $795.00
Budget Pool Care. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 3 listings from 2 sellers
AUD, before delivery. Each price shows when it was checked.
Genuine Pool Controls
3 listings from 2 sellers
Opens Budget Pool Care in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when chlorine output stays low after the salt level and water balance are right and the cell has been cleaned; Pool Controls gives no set life.
After replacing: No reset needed. Switch the chlorinator back on and set the cell output.
How to change the cell in your Pool Controls SG30
Watch the guide or follow the steps.
No clear video for this part yet. The steps cover it.
- 1Turn the chlorinator and the filter pump off, and close the valves either side of the cell if you have them.
- 2Disconnect the cell lead.
- 3Undo the cell housing nut and draw the old cell out of the housing.
- 4Check the cell O-ring and fit the new cell, then tighten the housing nut by hand.
- 5Reconnect the lead, start the pump and check for leaks, then turn the chlorinator back on and set the output.
Every number this part goes by
- Retail name:
- 00551335
Sellers list any of these; they are the same part.
About your Pool Controls SG30
Pool Controls salt chlorinator — SG Series salt chlorinator. Its cell is the SG30 replacement cell 00551335, part 00551335.
Where the model number is: The model and output are on the label on the power supply or control box near the pump. Switch the chlorinator and pump off at the power point before you touch the cell.
Fits these 3 Pool Controls models
Pool Controls3 models
Cell only: it fits your existing cell housing under the housing nut.
Common questions
- Which cell fits the Pool Controls SG30?
- The Pool Controls SG30 takes the Pool Controls SG30 replacement cell 00551335. Cell only: it fits your existing cell housing under the housing nut.
- Where can I buy the 00551335 in Australia?
- We track 2 Australian sellers for the 00551335; the lowest listed price when we last checked was A$795.00 at Budget Pool Care. Prices are re-checked daily and dated on this page.
- How do I fit the 00551335 in a Pool Controls SG30?
- 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A worn cell makes too little chlorine, so the water turns green or cloudy, and turning the output up only wears it faster.
- Is there anything to reset afterwards?
- No reset needed. Switch the chlorinator back on and set the cell output.
Something looks wrong with the SG30 match? . Reports go to a person, not a bot.