Evaporative cooler pad kit
Braemar Chillcel large pad 4-pack 114606 (90 mm, also fits Coolair)
114606
Fits 25 models
Wrong part, or your model missing? Tell us. A person checks every report.
GenuineGenuine Braemar
$486.00
HVAC Shop · 1 NovLowest genuine · HVAC Shop · checked 1 Nov
CompatibleCompatible option
$408.00
Plumbonline · 1 NovPlumbonline · checked 1 Nov
Check sellerCheck seller details
Genuine: made by Braemar. Compatible: another brand.Genuine is made by Braemar. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest compatibleLowest compatible price · $408.00
Plumbonline. Compare with genuine below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 3 sellers
AUD, before delivery. Each price shows when it was checked.
Compatible options
1 seller
Opens Plumbonline in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the pads are in poor condition or salted up, Seeley says; have them checked at the service before summer, at least every 2 years on a home cooler.
After replacing: No pad reminder to reset. After fitting new pads, run Pad Flush from the MagIQtouch settings menu if your cooler has one, or fill the tank, run the pump for about 5 minutes and drain it, to clear the smell of new pads.
How to change the 114606 evaporative cooler pad kit
Watch the guide or follow the steps.
No clear video for this part yet. The steps cover it.
- 1Turn the cooler off at the wall control, then switch it off at the isolating switch inside the cooler. Seeley recommends an authorised Seeley dealer or service agent for any work on the roof: climbing onto the roof is hazardous, and its manuals say maintenance is for a qualified, licensed technician.
- 2Working at heights needs extra safety precautions, Seeley warns: only go up if you can reach the cooler safely. Remove each pad frame: insert a flat screwdriver tip into the slot and lever until it lets go, pull the frame towards you until the internal side clips release, then pivot it outwards and lift it up.
- 3Pull out the pad pins and washers and lift out the old pads. On the LCS, note the rebates: each 120 mm pad goes where its rebate clears the float valve or drain valve.
- 4Fit the new Chillcel pads with the header block at the top, and push new pins and washers through until they sit flush. Check the pins and washers are not damaged.
- 5Refit the frames and clips, switch the power back on and run the cooler; never run it with the pad frames off. Flush the new pads: use Pad Flush in the MagIQtouch settings menu if you have it, or fill the tank, run the pump for about 5 minutes and drain it. Check that the pads wet evenly.
Every number this part goes by
- Retail name:
- 114606
Sellers list any of these; they are the same part.
Will it fit your appliance?
Type your model number and we'll check it against the makers' lists.
Fits these 25 models
Common questions
- What does the 114606 fit?
- The Braemar Chillcel large pad 4-pack 114606 (90 mm, also fits Coolair) fits 25 models, including the Braemar BM1150, Braemar BM900 and Braemar BMQ1150. Every one is listed on this page.
- Where can I buy the 114606 in Australia?
- We track 3 Australian sellers for the 114606; the lowest listed price when we last checked was A$408.00 at Plumbonline. Prices are re-checked daily and dated on this page.
- How do I fit the 114606?
- 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- Clogged pads pass less air and water, so the cooler blows warmer air, and old pads can smell musty.
- How do I reset the reminder?
- No pad reminder to reset. After fitting new pads, run Pad Flush from the MagIQtouch settings menu if your cooler has one, or fill the tank, run the pump for about 5 minutes and drain it, to clear the smell of new pads.
Something looks wrong with the 114606 match? . Reports go to a person, not a bot.