FitMatch

The Hurom HU-300 takes the Hurom silicone brushes for HU-300 and HU-400 (HX080) as its silicone part; Australian sellers list it from A$4.98 each as of 28 October 2026. Fitment confirmed against the manufacturer's compatibility list.

Your cold press juicer

Cold press juicer

Confirmed against Hurom's list

Not yours? Change
HX080

Takes the HX080

Silicone part · check the code on your old part.

Hurom lists two brush packs for the HU-300 (HX080 with the white and orange brush holder, HX084 also for the HU-300 MKII). Compare your old brushes with the photos.

Other Hurom cold press juicers that take the HX080

Genuine

$4.98 each

2-pack $9.95

Hurom Australia · 28 Oct

Compatible

See seller

No compatible seller tracked yet

Genuine: made by Hurom. Compatible: another brand.

Lowest price · $4.98 each · 2-pack $9.95

Hurom Australia. Every seller we track is listed below. Some links earn us a commission.

Open Hurom Australia

Compare 1 seller

AUD, before delivery. Each price shows when it was checked.

Hurom AustraliaGenuine · checked 28 Oct$4.98 each2-pack $9.95Open
Open cheapest seller · $4.98 each · 2-pack $9.95

Opens Hurom Australia in a new tab. Their page is the source of truth for price, delivery and returns.

How long it lasts

Replace it when the brushes are torn or worn; Hurom gives no set interval.

After replacing: No reset: Hurom juicers have no reminder for this part.

How to change the silicone part in your Hurom HU-300

Watch the guide or follow the steps.

No clear video for this part yet. The steps cover it.

  1. 1Switch the juicer off and unplug it. Open the hopper and lift out the screw, strainer and spinning brush.
  2. 2Separate the strainer from the spinning brush holder.
  3. 3Hold the outer side of each old silicone brush and pull it out in the direction of the arrow; pulling elsewhere can tear the brush or break the holder.
  4. 4Press each new brush into the holder, pulling the inner wing inward with your other hand so it sits in the grooves.
  5. 5Refit the strainer into the brush holder and reassemble the chamber.
Every number this part goes by
Retail name:
HX080

Sellers list any of these; they are the same part.

About your HU-300

Hurom juicer, cold press juicer — HU series. Its silicone part is the silicone brushes for HU-300 and HU-400 (HX080), part HX080.

Other silicone parts the maker lists for this cold press juicer:

Where the model number is: The model is on the label under the motor base, and on the box. Unplug the juicer and take the bowl off before you turn the base over.

Fits these 2 Hurom models

Hurom2 models

HU-300. Hurom lists two brush packs for the HU-300 (HX080 with the white and orange brush holder, HX084 also for the HU-300 MKII). Compare your old brushes with the photos.

Common questions
Which silicone part fits the Hurom HU-300?
The Hurom HU-300 takes the Hurom silicone brushes for HU-300 and HU-400 (HX080). Hurom lists two brush packs for the HU-300 (HX080 with the white and orange brush holder, HX084 also for the HU-300 MKII). Compare your old brushes with the photos.
Where can I buy the HX080 in Australia?
We track 1 Australian seller for the HX080; the lowest listed price when we last checked was A$4.98 at Hurom Australia. Prices are re-checked daily and dated on this page.
How do I fit the HX080 in a Hurom HU-300?
No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
What happens if I don't change it?
A worn or stretched seal or wiper lets juice leak round the bowl or the strainer.
Is there anything to reset afterwards?
No reset: Hurom juicers have no reminder for this part.

Something looks wrong with the HU-300 match? . Reports go to a person, not a bot.