How do I fit the 6101641?

No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.

What happens if I don't change it?

A clogged filter slows the cleaner and it picks up less; a torn one lets fine dirt pass straight back into the water.

Pool cleaner brush

Dolphin single-drive combined brush, grey (1 piece)

6101641

Fits 2 models · replace every 12 months

Wrong part, or your model missing? Tell us. A person checks every report.

GenuineGenuine Maytronics

$39.99

Maytronics Australia · 28 OctLowest genuine · Maytronics Australia · checked 28 Oct

CompatibleCompatible option

See seller

No compatible seller tracked yetNo compatible seller tracked yet

Genuine: made by Maytronics. Compatible: another brand.Genuine is made by Maytronics. Compatible is made by another brand. Check the seller's page for the size and models it fits.

Lowest price · $39.99

Maytronics Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.

Open Maytronics Australia · $39.99

Compare 1 seller

AUD, before delivery. Each price shows when it was checked.

Genuine Maytronics

1 seller

Maytronics AustraliaGenuine · checked 28 OctGenuine part · Lowest genuinechecked 28 Oct$39.99OpenGo to seller

Open cheapest seller · $39.99

Opens Maytronics Australia in a new tab. Their page is the source of truth for price, delivery and returns.

How long it lasts

Usually every 12 months (12 to 18 months, Maytronics says; sooner if the robot struggles to climb walls or the brushes are frayed, flattened or falling apart).

After replacing: No reset needed.

Not due yet?

Get a nudge when your pool cleaner brush is due — it's every 12 months. One email two weeks before, no newsletter. Manage or stop it anytime.

How to change the 6101641 pool cleaner brush

Watch the guide or follow the steps.

How to change the brush on your Dolphin robotic pool cleaner · Maytronics Australia (official)

1Turn the robot off at the power supply and unplug the cable. Take the robot out of the pool, let it drain and lay it upside down on a flat, clean surface.
2Grip the old brush firmly at one end and pull it away from the roller until it slides off.
3Line the new brush up with the roller grooves and push it on, starting at one end and working across.
4Check the brush is centred with no loose ends or gaps, then spin the roller by hand to make sure it moves freely.
5Replace every brush the model takes (2 or 4), then run a short cycle to check the robot grips and climbs.

Every number this part goes by6101641 · 6101641-R2

Retail name:: 6101641
Retail name:: 6101641-R2

Sellers list any of these; they are the same part.

Will it fit your appliance?

Type your model number and we'll check it against the makers' lists.

Your appliance model

Fits these 2 Maytronics modelsDolphin Supreme M3, Dolphin Supreme M4

Maytronics2 models

Takes 2 brushes.

Common questionsWhat does the 6101641 fit? · How often should I replace the 6101641? · Where can I buy the 6101641 in Australia?

What does the 6101641 fit?: The Dolphin single-drive combined brush, grey (1 piece) (part 6101641) fits the Maytronics Dolphin Supreme M3 and Dolphin Supreme M4.
How often should I replace the 6101641?: Every 12 months, or sooner if it looks worn.
Where can I buy the 6101641 in Australia?: We track 1 Australian seller for the 6101641; the lowest listed price when we last checked was A$39.99 at Maytronics Australia. Prices are re-checked daily and dated on this page.
How do I fit the 6101641?: No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
What happens if I don't change it?: A clogged filter slows the cleaner and it picks up less; a torn one lets fine dirt pass straight back into the water.
Is there anything to reset afterwards?: No reset needed.

Something looks wrong with the 6101641 match? . Reports go to a person, not a bot.