The Tineco Floor One S3 takes the Tineco HEPA filter for Floor One S3 (part 9FWFA110000) as its filter; Australian sellers list it from A$34.90 as of 2 November 2026. Fitment confirmed against the manufacturer's compatibility list.
Your hard floor cleaner
Tineco Floor One S3
Hard floor cleaner
Confirmed against Tineco's listConfirmed against Tineco's own compatibility list
Not yours? Change
Takes the 9FWFA110000 filter
HEPA filter for Floor One S3 · check the code printed on your old filter before ordering.
Your hard floor cleaner
Hard floor cleaner
Confirmed against Tineco's listConfirmed against Tineco's own compatibility list
Takes the 9FWFA110000
Filter · check the code on your old filter.
Other Tineco models and their rollers and filters
The 9FWFA110000 fits the Floor One S3 only. These Tineco models take a different filter:
GenuineGenuine Tineco
$34.90
Tineco Australia · 2 NovLowest genuine · Tineco Australia · checked 2 Nov
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Tineco. Compatible: another brand.Genuine is made by Tineco. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $34.90
Tineco Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Other parts this hard floor cleaner takes
- Tineco brush roller for Floor One S3, iFloor 3 and iFloor 2Open Amazon AU$11.00 each · 2-pack $21.99
The roller. Separate from the filter. Replace every 6 months.
Compare 2 sellers - Tineco Floor Cleaning Solution 1 LOpen Amazon AU$12.99
The cleaning solution. Refill when the bottle runs out: add it to the clean water tank as Tineco's manual for your model directs.
Compare 2 sellers
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
Opens Tineco Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it as needed: Tineco gives no interval for this filter. It says to rinse it under running water and let it dry completely before refitting, and supplies a spare to use while one dries.
After replacing: No reset: the maker's manual describes no replacement reminder for this part.
How to change the filter in your Tineco Floor One S3
Watch the guide or follow the steps.
- 1Take the cleaner off its base and press the dirty water tank release to lift the tank out.
- 2Pull the lid off the dirty water tank and empty it.
- 3Grasp the recessed areas on each side of the old filter and pull it straight up out of the tank lid.
- 4Fit the new filter into the lid, refit the lid and put the tank back until it clicks. Tineco says never to run the S3 without the filter.
Every number this part goes by
- Retail name:
- 9FWFA110000
Sellers list any of these; they are the same part.
About your Tineco Floor One S3
Tineco vacuum cleaner, hard floor cleaner — Floor One S3. Its filter is the HEPA filter for Floor One S3, part 9FWFA110000.
Other filters the maker lists for this hard floor cleaner: Tineco HEPA filter for Floor One S5, S6, S7 FlashDry, S7 Steam and iFloor 3 / 5. Tineco Australia also lists HEPA filter 9FWFA031100 (its S5-series filter) for this model.
Also in this hard floor cleaner: Tineco brush roller for Floor One S3, iFloor 3 and iFloor 2 (every 6 months), Tineco Floor Cleaning Solution 1 L.
Where the model number is: The rating label is on the underside or the back of the main body; the old part usually has its own code printed on it.
Fits this Tineco model
Tineco1 model
Common questions
- Which filter fits the Tineco Floor One S3?
- The Tineco Floor One S3 takes the Tineco HEPA filter for Floor One S3 (part 9FWFA110000).
- Where can I buy the 9FWFA110000 in Australia?
- We track 1 Australian seller for the 9FWFA110000; the lowest listed price when we last checked was A$34.90 at Tineco Australia. Prices are re-checked daily and dated on this page.
- How do I fit the 9FWFA110000 in a Tineco Floor One S3?
- No tools, a few minutes: 4 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- Suction drops and the vacuum may cut out on a blocked filter.
- Is there anything to reset afterwards?
- No reset: the maker's manual describes no replacement reminder for this part.
Something looks wrong with the Floor One S3 match? . Reports go to a person, not a bot.