FitMatch

The Billi Home C takes the Billi 0.2 micron Fibron XC replacement filter 994052 as its water filter; replace it every 12 months; Australian sellers list it from A$189.00 as of 6 November 2026. Fitment confirmed against the manufacturer's compatibility list.

Billi Home C

Your filtered water tap

Tap or under-sink system

Confirmed against Billi's list

Not yours? ChangeSave it · remind me
994052

Takes the 994052

Water filter · every 12 months · check the code on your old filter.

Other Billi filtered water taps that take the 994052

Genuine

$189.00

Cass Brothers · 6 Nov

Compatible

See seller

No compatible seller tracked yet

Genuine: made by Billi. Compatible: another brand. Check certification on the seller's page.

Lowest price · $189.00

Cass Brothers. Every seller we track is listed below. Some links earn us a commission.

Open Cass Brothers

Compare 7 sellers

AUD, before delivery. Each price shows when it was checked.

Cass BrothersGenuine · checked 6 Nov$189.00Open
eBay AUGenuine · checked 26 Oct$201.00Open
Amazon AUGenuine · checked 26 Oct$207.90Open
Billi AustraliaGenuine · checked 26 Oct$210.00Open
BuildmatGenuine · checked 6 Nov$225.00Open
Open cheapest seller · $189.00

Opens Cass Brothers in a new tab. Their page is the source of truth for price, delivery and returns.

Not due yet?

Get a nudge when your water filter is due — it's every 12 months. One email two weeks before, no newsletter. Manage or stop it anytime.

Also saves the model to a FitMatch account under this address; the email signs you in, no password.

How to change the water filter in your Billi Home C

Watch the guide or follow the steps.

Billi filter change: Eco, Sahara, Alpine models · Billi New Zealand Limited (official)
  1. 1Take the front panel off the under-bench unit (OmniOne and Home BCS: open the filter cover marked OPEN HERE).
  2. 2Release the pressure. Eco, Sahara, Alpine 125, Home BC, Home BA, Home B5000 Sparkling, Eco Sparkling and Quadra Sparkling: press the Pressure Relief button once. Other Quadra models: hold ON/OFF until the screen shows OVERRIDE OFF. OmniOne and Home BCS: press CHANGE FILTER. Home CS and Alpine Sparkling: turn off the blue tap under the bench and use the lever to release the pressure. Alpine 60/120, Home C, Home FT and Filter Tap: turn the water off at the wall, set the temperature control to OFF and open the tap.
  3. 3Hold the bottom of the filter, swing it towards you about 30 degrees, then pull it straight down out of the cradle. Wipe up any water in the tray.
  4. 4Remove the cardboard or foam spacer from under the new filter, push it right up into the cradle and swing it back until it locks.
  5. 5Flush: Quadra (not Sparkling), OmniOne and Home BCS flush themselves. Home CS and Alpine Sparkling: turn the blue tap back on and flush for 3 minutes. Alpine 60/120, Home C, Home FT and Filter Tap: turn the water back on and run the tap 2–3 minutes. All others, Quadra Sparkling included: run the chilled side until the flow stops, wait 10 minutes and repeat twice. Check for leaks and refit the panel.
Every number this part goes by
Retail name:
994052
Replaces:
994002

Sellers list any of these; they are the same part.

About your Home C

Billi filtered water tap, tap or under-sink system — Billi Home. Its water filter is the 0.2 micron Fibron XC replacement filter 994052, part 994052, changed every 12 months.

Other water filters the maker lists for this filtered water tap: Billi 5 micron Fibron X replacement filter 994051 (every 12 months). Billi's 5 micron filter also fits; Billi suggests it for high-use sites. The 0.2 micron 994052 is supplied as standard.

Where the model number is: On a boiling or chilled water tap the model is on the label on the unit under the bench, not on the tap itself. On an under-sink system it is on the filter head or housing; the cartridge code is printed on the old cartridge.

Fits these 20 Billi models

Home B5000 Sparkling. Billi's guide for this sparkling model says to change the filter every 6 months, sooner than the 12 months shown for the cartridge.

Alpine 120, Alpine 125, Alpine 60, Alpine Sparkling, Eco, Eco Sparkling, OmniOne, Quadra, Quadra Plus, Quadra Sparkling, Sahara, Sahara Plus. Billi's 0.2 micron filter also fits; Billi suggests it for homes and critical-care sites. The 5 micron 994051 is supplied as standard.

Common questions
Which water filter fits the Billi Home C?
The Billi Home C takes the Billi 0.2 micron Fibron XC replacement filter 994052.
How often should I replace the water filter in my Billi Home C?
Every 12 months. Flow slows and performance drops off as the filter fills up, so it's worth doing on time.
Where can I buy the 994052 in Australia?
We track 7 Australian sellers for the 994052; the lowest listed price when we last checked was A$189.00 at Cass Brothers. Prices are re-checked daily and dated on this page.
How do I fit the 994052 in a Billi Home C?
No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
What happens if I don't change it?
The carbon stops reducing chlorine taste and odour and the flow from the tap slows as the cartridge clogs; a boiling-water tap with a scale-reducing filter builds scale in its tank faster.
How do I reset the reminder?
Billi's guides give no separate reset step: the filter monitor counts cups and days, and Billi's service line (1800 812 321) can reprogram the interval if needed.

Something looks wrong with the Home C match? . Reports go to a person, not a bot.