Coolair evaporative cooler pads
Which cooling pad kit each of the 17 Coolair evaporative coolers sold in Australia takes, with dated prices from 2 Australian sellers, genuine and compatible side by side.
Most take the 114606 (9 of 17 models), from $408.00. Check yours below.
Braemar Chillcel large pad 4-pack 114606 (90 mm, also fits Coolair)takes 114606
- CPL1000takes 114606 · from $408.00View pad kit
- CPL1100takes 114606 · from $408.00View pad kit
- CPL850takes 114606 · from $408.00View pad kit
CPQ1100takes 114606 · from $408.00View pad kit- CPQ850takes 114606 · from $408.00View pad kit
- CPS1100takes 114606 · from $408.00View pad kit
- CPS850takes 114606 · from $408.00View pad kit
- CVP1100takes 114606 · from $408.00View pad kit
- CVP950takes 114606 · from $408.00View pad kit
Braemar Chillcel medium pad 4-pack 114590 (90 mm, also fits Coolair)takes 114590
- CPL450takes 114590 · from $339.00View pad kit
- CPL600takes 114590 · from $339.00View pad kit
- CPL700takes 114590 · from $339.00View pad kit
- CPQ450takes 114590 · from $339.00View pad kit
- CPQ700takes 114590 · from $339.00View pad kit
- CPS450takes 114590 · from $339.00View pad kit
- CPS700takes 114590 · from $339.00View pad kit
- CVP700takes 114590 · from $339.00View pad kit
How to change the pads in your Coolair cooler
Steps for the Braemar Chillcel large pad 4-pack 114606 (90 mm, also fits Coolair) (114606), the pad kit 9 Coolair models take.
No clear video for this pad kit yet. The steps cover it.
- 1Turn the cooler off at the wall control, then switch it off at the isolating switch inside the cooler. Seeley recommends an authorised Seeley dealer or service agent for any work on the roof: climbing onto the roof is hazardous, and its manuals say maintenance is for a qualified, licensed technician.
- 2Working at heights needs extra safety precautions, Seeley warns: only go up if you can reach the cooler safely. Remove each pad frame: insert a flat screwdriver tip into the slot and lever until it lets go, pull the frame towards you until the internal side clips release, then pivot it outwards and lift it up.
- 3Pull out the pad pins and washers and lift out the old pads. On the LCS, note the rebates: each 120 mm pad goes where its rebate clears the float valve or drain valve.
- 4Fit the new Chillcel pads with the header block at the top, and push new pins and washers through until they sit flush. Check the pins and washers are not damaged.
- 5Refit the frames and clips, switch the power back on and run the cooler; never run it with the pad frames off. Flush the new pads: use Pad Flush in the MagIQtouch settings menu if you have it, or fill the tank, run the pump for about 5 minutes and drain it. Check that the pads wet evenly.
After fitting the pads
No pad reminder to reset. After fitting new pads, run Pad Flush from the MagIQtouch settings menu if your cooler has one, or fill the tank, run the pump for about 5 minutes and drain it, to clear the smell of new pads.
Common questions
- What happens if I don't change the pad kit?
- Clogged pads pass less air and water, so the cooler blows warmer air, and old pads can smell musty.
- Does Coolair make a compatible pad kit?
- Braemar makes the genuine pad kit for Coolair models. Compatible pad kits for Coolair models are made by other companies to fit the same models, and Australian sellers we track list both; each part page shows the genuine and compatible prices side by side.
- Is there anything to do after changing the pads in a Coolair cooler?
- No pad reminder to reset. After fitting new pads, run Pad Flush from the MagIQtouch settings menu if your cooler has one, or fill the tank, run the pump for about 5 minutes and drain it, to clear the smell of new pads.
Brand names describe compatibility only; FitMatch is independent of Coolair. Fitment sources are recorded on every model page.