The Hurom HU-500 takes the Hurom silicone brushes for HU-500 and HU-300 (HX084) as its silicone part; Australian sellers list it from A$4.98 each as of 28 October 2026. Fitment confirmed against the manufacturer's compatibility list.
Your cold press juicer
Hurom HU-500
Cold press juicer
Confirmed against Hurom's listConfirmed against Hurom's own compatibility list
Not yours? Change
Takes the HX084 silicone part
silicone brushes for HU-500 and HU-300 (HX084) · check the code on your old part before ordering.
Your cold press juicer
Cold press juicer
Confirmed against Hurom's listConfirmed against Hurom's own compatibility list
Takes the HX084
Silicone part · check the code on your old part.
Other Hurom cold press juicers that take the HX084
GenuineGenuine Hurom
$4.98 each
2-pack $9.95
Hurom Australia · 28 OctLowest genuine · Hurom Australia · checked 28 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Hurom. Compatible: another brand.Genuine is made by Hurom. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $4.98 each · 2-pack $9.95
Hurom Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
Opens Hurom Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the brushes are torn or worn; Hurom gives no set interval.
After replacing: No reset: Hurom juicers have no reminder for this part.
How to change the silicone part in your Hurom HU-500
Watch the guide or follow the steps.
No clear video for this part yet. The steps cover it.
- 1Switch the juicer off and unplug it. Open the hopper and lift out the screw, strainer and spinning brush.
- 2Separate the strainer from the spinning brush holder.
- 3Hold the outer side of each old silicone brush and pull it out in the direction of the arrow; pulling elsewhere can tear the brush or break the holder.
- 4Press each new brush into the holder, pulling the inner wing inward with your other hand so it sits in the grooves.
- 5Refit the strainer into the brush holder and reassemble the chamber.
Every number this part goes by
- Retail name:
- HX084
Sellers list any of these; they are the same part.
About your Hurom HU-500
Hurom juicer, cold press juicer — HU series. Its silicone part is the silicone brushes for HU-500 and HU-300 (HX084), part HX084.
Other silicone parts the maker lists for this cold press juicer: Hurom silicone gasket for HU series (HX110). The silicone gasket for the HU-500.
Where the model number is: The model is on the label under the motor base, and on the box. Unplug the juicer and take the bowl off before you turn the base over.
Fits these 2 Hurom models
Common questions
- Which silicone part fits the Hurom HU-500?
- The Hurom HU-500 takes the Hurom silicone brushes for HU-500 and HU-300 (HX084).
- Where can I buy the HX084 in Australia?
- We track 1 Australian seller for the HX084; the lowest listed price when we last checked was A$4.98 at Hurom Australia. Prices are re-checked daily and dated on this page.
- How do I fit the HX084 in a Hurom HU-500?
- No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A worn or stretched seal or wiper lets juice leak round the bowl or the strainer.
- Is there anything to reset afterwards?
- No reset: Hurom juicers have no reminder for this part.
Something looks wrong with the HU-500 match? . Reports go to a person, not a bot.