The Ryobi R18HLTR38 takes the Ryobi RLTS2 pre-cut trimmer line, 2.0 mm (5 lengths) for Reel-Easy heads as its trimmer line. Fitment confirmed against the manufacturer's compatibility list.
Your line trimmer
Ryobi R18HLTR38
Line trimmer
Confirmed against Ryobi's listConfirmed against Ryobi's own compatibility list
Not yours? Change
Takes the RLTS2 trimmer line
RLTS2 pre-cut trimmer line, 2.0 mm (5 lengths) for Reel-Easy heads · check the code on your old part before ordering.
Your line trimmer
Line trimmer
Confirmed against Ryobi's listConfirmed against Ryobi's own compatibility list
Takes the RLTS2
Trimmer line · check the code on your old part.
Other Ryobi line trimmers that take the RLTS2
GenuineGenuine Ryobi
See seller
Ryobi Australia · 28 OctRyobi Australia · checked 28 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Ryobi. Compatible: another brand.Genuine is made by Ryobi. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
How long it lasts
Replace it when the line wears down and no longer feeds with a tap of the bump knob.
After replacing: No reset needed.
How to change the trimmer line in your Ryobi R18HLTR38
Watch the guide or follow the steps.
- 1Remove the battery pack. Lay the trimmer on a level surface, motor side down and guard side up.
- 2Turn the bump knob until the line on its centre lines up with the arrows on the outer spool.
- 3Push one pre-cut 2.0 mm line (about 3 m) through the eyelet on one side of the head until it comes out of the other side, with equal lengths each side.
- 4Turn the bump knob with the Speedwinder (or by hand) to wind the line in, until about 12 cm sticks out each side.
- 5Refit the battery, start the trimmer and tap the bump knob on the ground to feed more line as you work.
Every number this part goes by
- Retail name:
- 0355545
- Retail name:
- RLTS2
Sellers list any of these; they are the same part.
About your Ryobi R18HLTR38
Ryobi line trimmer — Reel-Easy (Speedwinder) bump-head line trimmers. Its trimmer line is the RLTS2 pre-cut trimmer line, 2.0 mm (5 lengths) for Reel-Easy heads, part RLTS2.
Where the model number is: The model is on the rating label on the motor housing or the shaft (Ryobi OLT1832, Ozito PXCLTS-018). Take the battery out or switch off before you turn the head over; the old spool's own code is often moulded on it.
Fits these 9 Ryobi models
Common questions
- Which trimmer line fits the Ryobi R18HLTR38?
- The Ryobi R18HLTR38 takes the Ryobi RLTS2 pre-cut trimmer line, 2.0 mm (5 lengths) for Reel-Easy heads.
- Where can I buy the RLTS2 in Australia?
- We link to 1 Australian seller for the RLTS2; the seller's page shows the current price.
- How do I fit the RLTS2 in a Ryobi R18HLTR38?
- No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- The trimmer stops cutting when the line runs out, and line of the wrong diameter jams the head or strains the motor.
- Is there anything to reset afterwards?
- No reset needed.
Something looks wrong with the R18HLTR38 match? . Reports go to a person, not a bot.