The Electrolux EWW1043R7SC takes the Electrolux front loader drain pump filter 140040243036 as its pump filter; Australian sellers list it from A$25.99 as of 28 October 2026. Fitment confirmed against the manufacturer's compatibility list.
Your front loader
Electrolux EWW1043R7SC
Front loader washing machine
Confirmed against Electrolux's listConfirmed against Electrolux's own compatibility list
Not yours? Change
Takes the 140040243036 pump filter
front loader drain pump filter 140040243036 · check the code printed on your old filter before ordering.
Your front loader
Front loader washing machine
Confirmed against Electrolux's listConfirmed against Electrolux's own compatibility list
Takes the 140040243036
Pump filter · check the code on your old filter.
Other Electrolux front loaders that take the 140040243036
GenuineGenuine Electrolux
$25.99
Electrolux Australia · 28 OctLowest genuine · Electrolux Australia · checked 28 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Electrolux. Compatible: another brand.Genuine is made by Electrolux. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $25.99
Electrolux Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 3 sellers
AUD, before delivery. Each price shows when it was checked.
Genuine Electrolux
3 sellers
Opens Electrolux Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when it is cracked or damaged or no longer seals; Electrolux says to examine the drain pump filter regularly and clean it when the machine does not drain, the drum cannot turn, it makes an unusual noise or shows a drain alarm.
After replacing: No reset needed. If the machine showed a drain alarm, clear the blockage, refit the filter and start a new programme.
How to change the pump filter in your Electrolux EWW1043R7SC
Watch the guide or follow the steps.
No clear video for this part yet. The steps cover it.
- 1Switch off and unplug the machine, and wait until the water inside is cold. Never remove the filter while the machine is running.
- 2Put a towel down and a shallow container under the drain pump door at the bottom front, then open the door.
- 3Press the two levers and pull the drainage duct forward to let the water out. Put the duct back and empty the container; repeat until no more water comes out.
- 4Push the duct back and turn the filter anticlockwise to remove it. Take out fluff and objects and check the pump impeller can turn; if it cannot, call the service centre.
- 5Clean the filter under the tap, put it back with the exposed section facing up and tighten it firmly so it does not leak, then close the door.
Every number this part goes by
- Retail name:
- 140040243036
- Replaces:
- 140040243028
Sellers list any of these; they are the same part.
About your Electrolux EWW1043R7SC
Electrolux washing machine, front loader washing machine — Washer-dryer combo (Electrolux). Its pump filter is the front loader drain pump filter 140040243036, part 140040243036.
Where the model number is: On a top loader the rating plate with the model is inside the lid or on the back; on a front loader, around the door opening or on the back. Switch the machine off at the wall before you take a filter out.
Fits these 23 models
Common questions
- Which pump filter fits the Electrolux EWW1043R7SC?
- The Electrolux EWW1043R7SC takes the Electrolux front loader drain pump filter 140040243036.
- Where can I buy the 140040243036 in Australia?
- We track 3 Australian sellers for the 140040243036; the lowest listed price when we last checked was A$25.99 at Electrolux Australia. Prices are re-checked daily and dated on this page.
- How do I fit the 140040243036 in an Electrolux EWW1043R7SC?
- 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A cracked or damaged pump filter can leak or let small objects through to the pump. A blocked one is cleaned, not changed: the machine stops draining until it is.
- Is there anything to reset afterwards?
- No reset needed. If the machine showed a drain alarm, clear the blockage, refit the filter and start a new programme.
Something looks wrong with the EWW1043R7SC match? . Reports go to a person, not a bot.