The Hurom HU-700 takes the Hurom silicone brushes for HU-700 and HF Gen 1 (HX081) as its silicone part; Australian sellers list it from A$4.98 each as of 28 October 2026. Fitment confirmed against the manufacturer's compatibility list.
Your cold press juicer
Hurom HU-700
Cold press juicer
Confirmed against Hurom's listConfirmed against Hurom's own compatibility list
Not yours? Change
Takes the HX081 silicone part
silicone brushes for HU-700 and HF Gen 1 (HX081) · check the code on your old part before ordering.
Your cold press juicer
Cold press juicer
Confirmed against Hurom's listConfirmed against Hurom's own compatibility list
Takes the HX081
Silicone part · check the code on your old part.
Other Hurom models and their filters and parts
The HX081 fits the HU-700 only. These Hurom models take a different silicone part:
GenuineGenuine Hurom
$4.98 each
2-pack $9.95
Hurom Australia · 28 OctLowest genuine · Hurom Australia · checked 28 Oct
CompatibleCompatible option
See seller
No compatible seller tracked yetNo compatible seller tracked yet
Genuine: made by Hurom. Compatible: another brand.Genuine is made by Hurom. Compatible is made by another brand. Check the seller's page for the size and models it fits.
Lowest price · $4.98 each · 2-pack $9.95
Hurom Australia. Every seller we track is listed below. Some links earn us a commission. Some seller links earn us a commission, at no extra cost to you.
Compare 1 seller
AUD, before delivery. Each price shows when it was checked.
Opens Hurom Australia in a new tab. Their page is the source of truth for price, delivery and returns.
How long it lasts
Replace it when the brushes are torn or worn; Hurom gives no set interval.
After replacing: No reset: Hurom juicers have no reminder for this part.
How to change the silicone part in your Hurom HU-700
Watch the guide or follow the steps.
No clear video for this part yet. The steps cover it.
- 1Switch the juicer off and unplug it. Open the hopper and lift out the screw, strainer and spinning brush.
- 2Separate the strainer from the spinning brush holder.
- 3Hold the outer side of each old silicone brush and pull it out in the direction of the arrow; pulling elsewhere can tear the brush or break the holder.
- 4Press each new brush into the holder, pulling the inner wing inward with your other hand so it sits in the grooves.
- 5Refit the strainer into the brush holder and reassemble the chamber.
Every number this part goes by
- Retail name:
- HX081
Sellers list any of these; they are the same part.
About your Hurom HU-700
Hurom juicer, cold press juicer — HU series. Its silicone part is the silicone brushes for HU-700 and HF Gen 1 (HX081), part HX081.
Other silicone parts the maker lists for this cold press juicer: Hurom silicone gasket for HU series (HX110). The silicone gasket Hurom's part data lists for the HU-700.
Where the model number is: The model is on the label under the motor base, and on the box. Unplug the juicer and take the bowl off before you turn the base over.
Fits this Hurom model
Hurom1 model
Common questions
- Which silicone part fits the Hurom HU-700?
- The Hurom HU-700 takes the Hurom silicone brushes for HU-700 and HF Gen 1 (HX081).
- Where can I buy the HX081 in Australia?
- We track 1 Australian seller for the HX081; the lowest listed price when we last checked was A$4.98 at Hurom Australia. Prices are re-checked daily and dated on this page.
- How do I fit the HX081 in a Hurom HU-700?
- No tools, a few minutes: 5 steps, listed on this page with the replacement video where the maker has one.
- What happens if I don't change it?
- A worn or stretched seal or wiper lets juice leak round the bowl or the strainer.
- Is there anything to reset afterwards?
- No reset: Hurom juicers have no reminder for this part.
Something looks wrong with the HU-700 match? . Reports go to a person, not a bot.