Baratza grinder burrs by part number

The S1 cone burr already fitted in its holder, with the screw, for Baratza's Sette grinders. Baratza says the S1 comes standard in every Sette, and the Sette 30, 270 and 270Wi all list 40 mm S1 conical burrs. The holder drops out from under the grinder with the grind adjustment assembly, so swapping the whole holder needs no hex key.

After the change: No reset: the grinder has no reminder for the burrs.

Fits 3 Baratza models: Sette 270, Sette 270Wi, Sette 30.

The S1 cone burr on its own, without the holder, for Baratza's Sette grinders. Baratza says the S1 comes standard in every Sette. To fit it you take the burr holder out of the grinder, undo the bolt under the holder with the 5 mm hex key that comes with the Sette, and tap the old burr off. Baratza also sells the burr ready-fitted in a holder.

After the change: No reset: the grinder has no reminder for the burrs.

Fits 3 Baratza models: Sette 270, Sette 270Wi, Sette 30.

One 54 mm ceramic flat burr with three screws, from Baratza's parts store. The grinder uses two, upper and lower, so order two to replace both. Baratza's page doesn't name the grinders, but the Vario+ and Forté AP are both listed with 54 mm flat ceramic burrs, which Baratza says generally last around 10 years of standard home use.

After the change: No reset: the grinder has no reminder for the burrs. Recalibrate the burrs after fitting new ones, as the manual describes.

Fits 2 Baratza models: Forté AP, Vario+.

A pair of 54 mm steel flat burrs with six screws, from Baratza's parts store. Baratza's page doesn't name the grinders, but the Vario W+ and Forté BG are both listed with 54 mm flat steel burrs. Baratza says the replaceable burrs in the Vario range generally last around 10 years of standard home use. Calibrate the burrs after fitting.

After the change: No reset: the grinder has no reminder for the burrs. Recalibrate the burrs after fitting new ones, as the manual describes.

Fits 2 Baratza models: Forté BG, Vario W+.

Baratza's outer ring burr in its holder for the Encore and Virtuoso+ conical grinders. It is the burr you lift out from under the hopper by its two tabs, with no tools. Baratza says it is not for the Encore ESP or ESP Pro, which have their own ring burrs. The cone burr below it is a separate part.

After the change: No reset: the grinder has no reminder for the burrs.

Fits 2 Baratza models: Encore, Virtuoso+.

Baratza's 40 mm steel M2 cone burr with the quick-release fitting, for the Encore ESP and Encore ESP Pro only. It is the inner, lower burr. On these grinders it comes out by hand: twist off the quick-release knob on top of it and lift it out, keeping the parts below it in order.

After the change: No reset: the grinder has no reminder for the burrs.

Fits 2 Baratza models: Encore ESP, Encore ESP Pro.

The outer ring burr and holder for Baratza's Encore ESP. Baratza says it fits only the Encore ESP (ZCG495B and ZCG495W); the original Encore, Virtuoso+ and Encore ESP Pro each take a different ring burr. It lifts out by its two tabs once the hopper is off and the adjustment ring is turned fully anticlockwise.

After the change: No reset: the grinder has no reminder for the burrs.

Fits the Encore ESP.

The outer ring burr and holder for Baratza's Encore ESP Pro (ZCG595). Baratza says it fits only the ESP Pro; the Encore, Encore ESP and Virtuoso+ take other ring burrs. To reach it you turn the grind setting collar fully anticlockwise and lift it off, undo the quick-release knob, then lift out the flow control disk and the burrs.

After the change: No reset: the grinder has no reminder for the burrs.

Fits the Encore ESP Pro.

Baratza's threaded M2 cone burr, the 40 mm steel inner burr the Virtuoso+ comes with. Baratza says it also fits the Encore and some discontinued conical grinders. Changing it takes about 20 minutes: the case and gearbox come off and the reverse-threaded burr unscrews from the drive shaft. For the Encore ESP and ESP Pro, Baratza sells a quick-release M2 instead.

After the change: No reset: the grinder has no reminder for the burrs.

Fits the Virtuoso+.

Baratza's M3 cone burr, the 40 mm steel inner burr the Encore comes with. Baratza says it fits the Encore, Virtuoso+ and some discontinued conical grinders. Changing it is a moderate job of about 20 minutes: the case and gearbox come off and the burr unscrews from the drive shaft, so most owners only change the ring burr above it.

After the change: No reset: the grinder has no reminder for the burrs.

Fits the Encore.